BU208 DATASHEET PDFBU208 DATASHEET PDF

BU datasheet, BU pdf, BU data sheet, datasheet, data sheet, pdf, Central Semiconductor, Leaded Power Transistor General Purpose. BU datasheet, BU circuit, BU data sheet: MOSPEC – POWER TRANSISTORS(A,V,55W),alldatasheet, datasheet, Datasheet search. BU Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for BU Bipolar Transistors – BJT.

Author: Nekree Arar
Country: Senegal
Language: English (Spanish)
Genre: Music
Published (Last): 2 June 2010
Pages: 180
PDF File Size: 5.30 Mb
ePub File Size: 4.77 Mb
ISBN: 239-7-65718-768-7
Downloads: 89562
Price: Free* [*Free Regsitration Required]
Uploader: Sham

BU Datasheet pdf – Leaded Power Transistor General Purpose – Central Semiconductor

This sample of the output voltage is compared with the reference voltage from D39 in ICIO, which drives the datasheet stabiliser element TR9. Information across the k resistor passes through a 1uF capacitor to bi208 base of a transistor. The figure of 2. In a series of datasgeet 20 test flashovers, which were induced by tuning and loading a W1SL-type MHz amplifier with these modifications incorporated for full output power into a dummy load, removing the load and applying full drive, there was no damage to any part of the amplifier or its power supply apart from blown fuses in the ehv supply and normal operation could be resumed as soon as the fuses had been replaced and the load had been reconnected.

The output ripple of the bias supply is less than 2mV pk-pk. Look at the picture and pay attention to the control currents base currents of the transistors: The bu2008 of R68 should be chosen to pass about 5mA when the ptt switch in Fig 6 is open-circuit; the formula is; Fig 6.

Because of that, the transistor is heating itself and everything in its proximity. Four leads emerge from some other types, such as two-gate FETs. Suggested air-flow switch arrangement Setting-up Like most logic circuits of this type setting-up is tedious rather than difficult. Placement of leads and different datawheet types for some commonly used transistors are in diagram 4.

The typical gain curve peaks at less than High power transistors are different from low-to-medium power, both in size datahseet in shape. The “turn-on” resistor – the resistor on the base, is 1M.

  2X062H DATASHEET PDF

If an oscilloscope is available the stability and ripple rejection can be checked.

These are general purpose transistors. The gain is equal to:. Listening to a 50Hz noise is not very interesting, so you could connect to points 1 and 2 some low frequency signal source CD player or a microphone. The supply voltage for the op-amps is produced in a slightly unorthodox manner by D45 and D46 and the associated capacitors; these form a voltage doubler for which the zener diodes provide protection against stray transient voltages across the rails and enable the screen supply op-amps to be powered from a spare 6.

Check Hiatt switching the supply to the receive position causes the supply output voltage to be the same as the input voltage. Connect the voltmeter to the output of channel A pin Transistors used with very high frequencies like BFR14 have pins shaped differently.

And all these transistors operate in a manner shown in our experiments, which means that by building this example, you’re actually building a basic building block of electronics. The board is quite densely laid out and is not recommended as a first exercise in pcb construction; the authors have assumed that anyone considering building a high-power amplifier will not he a complete novice iii the art of home-brewing.

Variable capacitor C and coil L form a parallel oscillating circuit which is used to pick out the signal of a radio station out of many different signals of different frequencies.

Suggested screen grid circuitry. This “overcompensation” technique can be useful for ensuring stability in regulator circuits where the total open-loop gain is extremely high, as it is in this design. If particularly esoteric devices with very high hk are used it may be necessary to increase the values of R50 and R52, which set the short-circuit current. These are for initial setting-up of the standing currents, as discussed later. Selecting the correct transistor for a circuit is based on the following characteristics: Note that an internally-compensated op-amp such as the cannot be used in this circuit.

  INTOXICACION COCAINA PDF

BU 데이터시트(PDF) – Central Semiconductor Corp

Original transistor were made from germanium, but they were very temperature-sensitive. For PNP transistors the battery is reversed. If a simulated ehv sample is then applied to pin 36, the “ready” relay should operate.

For example, maximum ratings for a BC transistor are: Beginners usually assume these two are the same which is a mistake. Resistor R isn’t really necessary, but if you don’t use it, you mustn’t turn the potentiometer pot to its high position, because that would destroy the transistor – this is because the DC voltage UBE voltage between the base and the emittershould not be higher than 0. In view of both the high voltages present on the pcb and the high impendances involved in the cmos circuitry, it is strongly recommended that when the board has been completed and tested the track side is thoroughly defluxed with an appropriate solvent, such as the aerosol solvent cleaner available from Electromail under the stock numberand then given several coats of pcb lacquer; the “anti-corona” aerosol from the same source stock number is excellent for this purpose.

BU208 Datasheet, Equivalent, Cross Reference Search

The inductor is formed by winding about 10 turns of 22swg enamelled wire around the body of a low-value 2W resistor. Next, check that the voltage of channel A is variable by means of RV15; some 30V variation should be available.

The first stage should divide the ehv down to perhaps I0X0V, and should ideally have a zcner diode of a suitable voltage rating in parallel with the lower resistor in the divider chain to limit the divider output voltage if the resistor fails open-circuit or loses its earth connection. Mains distribution Next, check that the voltage of channel A is variable by means of RV15; some 30V variation should be available.

Jun 22, 7, 1, The performance of this supply is also good.